Fiberlock IAQ 9000 Waterproof Coating

Fiberlock IAQ 9000 is a low-odor waterproofing coating that is specially formulated to stop water from penetrating through a variety of interior and exterior surfaces including above or below grade masonry walls, cinder and concrete block, stucco, brick, retaining walls, and foundations. This latex based formula stops 10 psi of water pressure and reduces radon gas penetration. Fiberlock IAQ 9000 contains an EPA-registered fungicide to help prevent mold from growing on the surface of the cured film. This fast-drying formula may be applied easily with a brush and/or roller on dry surfaces and cleans up easily with soap and water.

Product Data Sheet
Material Safety Data Sheet (MSDS)

Fiberlock IAQ 4000 Direct-To-Metal Primer

Fiberlock IAQ 4000 is a rust inhibiting 100% acrylic latex metal coating for use on ferrous metal, galvanized metal and other surfaces exposed to general industrial and atmospheric conditions. Fiberlock IAQ 4000 has excellent water resistance and excellent resistance to most alkalis, detergents and mild acids. This acrylic latex metal coating does not contain the flammable solvents contained in other rust inhibiting paints, has low odor and fast recoatability. Fiberlock IAQ 4000 is ideal for coating both new and previously painted roof decks, metal paneling, structural steel, corrugated metal siding, and miscellaneous iron and bar joist.

PROPERTIES

Percent Solids: 48.36% by weight 33.84% by volume

Volatile: Principally water

Viscosity at 70°F: 90-100 Krebs Units

Weight per gallon @ 70°F: 10.7 lbs/gal

Flash Point: None (water-based)

Shelf Life: @ 70°F, 36 months minimum (in original factory sealed containers)

Finish: Semi-gloss

Coverage: Brush or Roll: 400-450 ft2/gal Spray: 200-225 ft2/gal

Dry Time @ 70°F: To touch: 1 hour To recoat: 1 hour Full cure: 10 days

Fire rating ASTM E84-81a: Class "A" Flame Spread: 0 Fuel Contribution: 0

Smoke Developed: 5

Packaged: 1, 5, and 55 gallon containers

Product Data Sheet
Material Safety Data Sheet (MSDS)

A-B-C Asbestos Encapsulant Binding Compound

When high costs make asbestos removal an unsuitable choice, you can manage asbestos in-place through encapsulation. A-B-C Asbestos Binding Compound, our flagship product, is the world's most successful encapsulation solution. This highly effective, industry-standard, high-solids encapsulant meets Environmental Protection Agency guidelines. It's ideal for sealing in asbestos-containing material, as laboratory tests have shown. The EPA recommends you apply two coats for maximum effectiveness. Dilute the first coat with water so it can penetrate and bind the asbestos-containing material. Then apply the second coat at full strength. A-B-C completely encapsulates all fibers beneath a flexible, impact-resistant seal. A-B-C can also be diluted to perform just about any asbestos control task, from encapsulation to pre-removal wetting or room misting to post-removal lockdown of asbestos fibers.

Product No.: 6421 Off-White, 6422 Clear (when dry),

A-B-C Asbestos Binding Compound is a high solids asbestos encapsulant, designed to encapsulate and seal friable Asbestos Containing Material (ACM) such as fireproofing and insulation materials. A-B-C is an important tool for coping with the health hazards associated with exposure to asbestos fibers. In 1978, A-B-C was tested for the EPA by Battelle Laboratories of Columbus, Ohio, and found to meet the requirements for the effective encapsulation and removal of ACM. In addition,A-B-C received German approval following a thorough evaluation conducted at the University. The high solids, nonflammable composition of A-B-C allows for dilution with water to provide maximum flexibility for specific asbestos abatement needs, including removal/lockdown, penetrating encapsulation and bridging encapsulation. Since 1978, A-B-C has provided exceptional long lasting performance in asbestos abatement worldwide.

PROPERTIES

Solids by weight: 60 ± 2%

Volatile: Water

Average particle size: 0.2 microns

Viscosity @ 77°F: 60-65 Krebs Units

Weight per gallon @ 77°F: 9.1 ± 0.2 lbs/gal

Film Hardness: Excellent

Film Flexibility: Excellent

Impact Resistance: Excellent

Water resistance of dry film: Excellent

Bridging effectiveness: Excellent

Bond strength to concrete/steel: Excellent

Coverage: 50-100 sq. ft./gal (depending on the porosity of substrate and type of application)

Flash point: Tag Closed Cup, Non-combustible (water based)

Dry Time @ 77°F, 50% R.H.: To touch 1-2 hours Full cure, 12- 24 days.

Shelf Life @ 77° F: 36 months minimum (in original factory sealed containers)

Odor: Virtually odorless

Finish: Moderate gloss

Fire rating ASTM E84: Class “A” (Southwest Research Institute) Flame Spread: 10 Fuel Contribution: 10 Smoke Density: 5

Packaged: 5 gallon

Product Data Sheet
Material Safety Data Sheet (MSDS)

L-B-C Lead Barrier Compound Encapsulant

L-B-C is a high-solids, elastomeric-thermoplastic, water-based copolymer that meets or exceeds all projected federal, state and local standards for lead-based paint encapsulants. Blended specifically to form a durable and flexible encapsulant barrier between lead-based pain and the environment, L-B-C has been independently tested to the ASTM E-1795 requirements for Category III (Type III- Interior/Exterior) encapsulants. E-1795 is the principle performance standard required, adopted and/or incorporated by reference into lead paint abatement rules and regulations at the federal, state and local levels. L-B-C has been certified by Massachusetts (No. DL-12362), authorized by the states of Connecticut, Ohio, New York, Maryland, Minnesota, and Colorado. L-B-C is accepted for use in all 50 states. L-B-C has also been classified by Underwriters Laboratories (UL®). L-B-C is environmentally friendly and complies with all federal and state VOC requirements.

L-B-C Lead Barrier Compound (MSDS)

Lag Kote II Encapsulant Coating (5-Gal)

Lag-Kote is a 100% acrylic, high-solids encasement/encapsulation coating, specifically formulated for application over a variety of asbestos containing materials. Tested and EPA accepted at Battelle Laboratories of Columbus, Ohio, under EPA Contract #68-03-2552-T2005, Lag-Kote was found to be an acceptable encapsulant. Lag-Kote was designed to encase asbestos-containing spray-on fireproofing, transite, and thermal insulation. Lag-Kote's viscous formulation minimizes dripping, clean-up and product waste. Lag-Kote provides a smooth, washable, aesthetically superior finish that will provide years of lasting protection. Lag-Kote has excellent resistance to alkalis and can be applied directly over galvanized metal, ferrous metal, masonry or other sound surfaces. UV inhibitors make Lag-Kote suitable for encasement of exterior asbestos containing materials including transite. Lag-Kote is water-base and non-toxic.

DESCRIPTION:

Product No.: 6420 white

Lag-Kote is a 100% acrylic, high solids encasement/encapsulation coating specifically formulated for application over a variety of asbestos containing materials (ACM). Lag-Kote is an EPA accepted coating for the encasement/encapsulation of ACM. It was tested at Battelle Columbus Laboratories of Columbus, Ohio, under EPA Contract

# 08-03-2552-T2005, and found to be acceptable as an encapsulant.

Designed to encase spray-on fireproofing, asbestos-containing plasters and paints, transite, and asbestos-containing thermal insulation, Lag-Kote’s viscous formulation minimizes dripping, clean-up and product waste. Lag-Kote provides a smooth, washable, aesthetically-superior finish that will provide years of lasting protection. Lag-Kote has excellent resistance to alkalis and can be applied directly over galvanized metal,

wood, masonry or other sound surfaces. UV inhibitors make Lag-Kote suitable for encasement of exterior asbestos containing materials. Lag-Kote yields an opaque, bright white finish, or can be factory tinted to meet specific color requirements. Lag-Kote is water-based and non-toxic.

PROPERTIES:

Solids by Weight: 48 +/-2%

Volatile: Water

Average particle size: 0.2 microns

Viscosity @ 77°F: 120-130 Krebs Units

Weight per gallon @ 77°F: 11.7 lbs.

Film Hardness: Excellent

Film Flexibility: Excellent

Impact Resistance: Excellent

Water resistance of dry film: Excellent

Bond Strength to concrete/steel: Excellent

Coverage:

Brush: 125-175 sq.ft./gal. (5 dry mils)

Airless Spray: 600 sq.ft./gal. (1 dry mil)

Fire Rating ASTM E84-81a: Class “A”

(Southwest Research Institute)

Flame Spread: 5

Fuel Contribution: 0

Smoke Density: 0

Dry Time 1 - 2 hours

Shelf Life: @ 77°F, 36 months minimum, (in

original factory sealed containers)

Odor: Applied indoors, virtually odorless

Finish: Slight gloss

Color: Bright White

Packaged: 5 gallon pail

Product Data Sheet

Material Safety Data Sheet (MSDS)