Floor Coating & Painter Application Tools
100% SOLIDS EPOXY FLOOR COATINGS • NORKLAD 100/200 • 100% SOLIDS UV EPOXY • 100% SOLIDS LOW VISCOSITY
 

100% Solids Epoxy Floor Coatings

Here you will find all your 100% Solids Epoxy Coating needs. We carry all multiple types of 100% solids such as clear bases, colored bases, UV clear coats, fast cures & low viscosity primers. If you can't find something you are looking for, please give is a call at 1-800-227-8479.

100% Solids Basecoat & Clearcoat Epoxy Floor Coatings

Here is what is included on this page:

Norklad 100M Clear Coat | Norklad 100 UV Clear | Norklad 200 Colored Base Coat | Norklad 200 Fast Cure Colored Base Coat | Norklad 200 LVP Colored Primer Coat | 100% Solids Epoxy Floor Coatings


Norklad 100 - 100% Solids Epoxy Clear CoatNorklad 100-M - 100% Solids Epoxy Clear Coat

Sizes:

.75 Gallon (75-100+ sq/ft)
1.5 Gallon (175+ sq/ft)
3 Gallon (400+ sq/ft)

Norklad 100-M is a two component 100% solids epoxy broadcast coat that can be filled with decorative chips and colored sand mixtures to provide an infinite array of color schemes or patterns. It is 100% solids therefore has low odor, no flammability, and is self-leveling. When applied at 100 sq/ft per gallon, Norklad 100-M will self-level to a glasslike surface.

When to use Norklad 100-M: 100% solids is recommended for warehouses, kitchens, restrooms, and other areas where either a high build clear product is needed or where a decorative filled floor is desired. Ideal for full broadcast terrazzo or colorchip floors. 100% solids is the industry standard for high-end commercial epoxy flooring.

Norklad 100-M 100% Solids Clear CoatProduct Data Sheet

SOLIDS BY WEIGHT: 100%

SOLIDS BY VOLUME: 100%

VOLATILE ORGANIC CONTENT: Zero pounds per gallon

COLOR: Clear

RECOMMENDED FILM THICKNESS: 16-18 mils

COVERAGE PER GALLON: 90-100 square feet per gallon @ 16-18 mils

PACKAGING INFORMATION
1.5 gallon kits (2.95 gallons net approximately)

MIX RATIO: 9.0 pounds part A (.99 gallons) to 4.15 pounds part B (.49 gallons) (volumes approx.)

FINISH CHARACTERISTICS: Gloss (60 to 90 @ 60 degrees @ Erichsen glossmeter)

ABRASION RESISTANCE: Taber abraser CS-17 calibrase wheel with 1000 gram total load and 500 cycles = 36 mg loss

FLEXURAL STRENGTH: 7,400 psi @ ASTM D790

COMPRESSIVE STRENGTH: 11,200 psi @ ASTM D695

ADHESION: 350 psi @ elcometer (concrete failure, no delamination)

VISCOSITY: Mixed = 700-1000 cps (typical)

TENSILE STRENGTH: 7,600 psi @ ASTM D638

ULTIMATE ELONGATION: 4.1%

GARDNER VARIABLE IMPACTOR: 50 inch pounds direct – passed

HARDNESS: Shore D = 81

CURE SCHEDULE:

pot life – 1 1/2 gallon volume ……..……... 20-30 minutes @ 70° F
tack free (dry to touch)…………....…………..…6-8 hours @ 70° F
recoat or topcoat.....…………….…………..... 10-16 hours @ 70°F
light foot traffic...…………………………..……14-18 hours @ 70°F
full cure (heavy traffic)... ………..…………...…....2-7 days @ 70°F

APPLICATION TEMPERATURE: 55-90 degrees F

CHEMICAL RESISTANCE:

REAGENT RATING
butanol C
xylene C
1, 1, 1 trichloroethane B
MEK A
methanol A
ethyl alcohol C
skydrol B
10% sodium hydroxide E
50% sodium hydroxide D
10% sulfuric acid C
70% sulfuric acid A
10% HC1 (aq) C
5% acetic acid B

Rating key: A - not recommended, B - 2 hour term splash spill, C - 8 hour term splash spill, D - 72 hour immersion, E - long term immersion. NOTE: extensive chemical resistance information is available through your sales representative.

TOPCOAT: Urethane topcoat is recommended for added UV-Resistance if exposed to sunlight. Norklad 100 can easily coat over any solvent or waterborne epoxies. If used alone, it is recommended that a primer coat be used to prevent outgassing/blistering. *For best results, apply with a ¼” nap roller and/or squeegee

SURFACE PREPARATION: The most suitable surface preparation would be a fine brush blast (shot blast or diamond grind) to remove all laitance and provide a suitable profile. All dirt, foreign contaminants, oil and laitance must be removed to assure a trouble free bond to the substrate. A test should be made to determine that the concrete is dry; this can be done by placing a 4'x4' plastic sheet on the substrate and taping down the edges. If after 24 hours, the substrate is still dry below the plastic sheet, then the substrate is dry enough to start coating. The plastic sheet testing is also a good method to determine if any hydrostatic pressure problems exist that may later cause disbonding. Apply your basecoat and colorchips and allow to sufficiently cure. (wait until you can no longer leave an imprint of your finger in the coating. i.

PRODUCT MIXING: This product has a mix ratio of 9.0# part A to 4.15# part B. Standard packages are packaged in 1.5-gal kits. (1 gal of part a (resin) and half gallon of part b (hardener). They are in pre-measured kits and should be mixed as supplied in the kit. We highly recommend that the kits not be broken down unless suitable weighing equipment is available. After the two parts are combined, mix well with slow speed mixing equipment such as a jiffy mixer until the material is thoroughly mixed and streak free. After mixing, transfer the mixed material to another pail (the transfer pail) and again remix. The material in the transfer pail is now ready to be applied onto your basecoat. Improper mixing may result in product failure.

PRODUCT APPLICATION: The mixed material can be applied by brush, roller or a serrated squeegee and then back rolled as long as the appropriate thickness recommendations are maintained. Then broadcast aggregate into the coating while wet. Maintain temperatures and relative humidity within the recommended ranges during the application and curing process. If concrete conditions or over aggressive mixing causes air entrapment, then an air release roller tool should be used prior to the coating tacking off. This product can be used with random chip broadcasts, full chip broadcasts, or colored quartz.

RECOAT OR TOPCOATING: If you opt to recoat or topcoat this product, you must first be sure that the coating has tacked off before recoating. Always remember that colder temperatures will require more cure time for the product before recoating or topcoating can commence. Before recoating or topcoating, check the coating to insure no epoxy blushes were developed (a whitish, greasy film or deglossing). If a blush is present, it must be removed prior to topcoating or recoating. We recommend topcoating with a urethane product to assist in UV-resistance.

CLEANUP: Use xylol xylene.

 
75 sq/ft
150 sq/ft
300 sq/ft
1,500 sq/ft
 
Buy Now
Buy Now
Buy Now
Buy Now

Norklad 100 - 100% Solids UV Stable Epoxy Clear CoatNorklad 100 - 100% Solids UV Stable Epoxy Clear Coat

 

 

 


Buy Now


Norklad 200 - 100% Solids Epoxy Colored Base CoatNorklad 200 - 100% Solids Epoxy Colored Base Coat

Norklad 200 is a two component 100% solids epoxy colored coating designed for applications where a high build colorfast impact resistant floor is needed. It can be used as durable color coat for for maximum durability or as a colored basecoat for color chip broadcasts. 100% solids epoxy is considered the industry standard for high-end flooring due to the fact that it is 4x stronger than concrete and has no voc, no flammability and can be applied as thick or thin as you need it.

It's recommend to squeegee this product out and apply 100-125 sq/ft per gallon (approx.14-16 mils) and back roll it with a shed-resistant roller to even it out. It has a very fast pot life (30 minutes) once it's mixed with the converter. Once you get the product out of your mixing bucket it takes much longer for it to tack off.

Norklad 200 100% Solids Colored Basecoat
Product Data Sheet
MSDS

CURE SCHEDULE:
pot life – 1 1/2 gallon volume ………..………30-50 minutes @ 70° F
tack free (dry to touch)……….…...……………..…5-8 hours @ 70° F
recoat or topcoat.....…………….……..………..... 8-12 hours @ 70°F
light foot traffic...……………...……………..……12-14 hours @ 70°F
full cure (heavy traffic)... ..……………………...…....2-7 days @ 70°F

APPLICATION TEMPERATURE: 60-90 degrees F with relative humidity below 85%

SOLIDS BY WEIGHT: 100% (+/- 1%)
SOLIDS BY VOLUME: 100% (+/- 1%)
VOLATILE ORGANIC CONTENT: Nearly zero pounds per gallon
COLORS: Light Gray, Medium Gray, Dark Gray, Beige, Tan, Brown, Tile Red, Blue, Light Blue,
RECOMMENDED FILM THICKNESS: 12-30 mils
COVERAGE PER GALLON: 53-130 square feet per gallon @ 12-30 mils
PACKAGING INFORMATION 3 gallon kits (2.9 – 3.0 gallons net approximately)
MIX RATIO: 12 pounds (1 gallon) part A to 4.15 pounds (.50 gallons) part B (volumes approx.)
FINISH CHARACTERISTICS: Gloss (70-95 at 60 degrees @ Erichsen glossmeter)
ABRASION RESISTANCE: Taber abraser CS-17 calibrase wheel with 1000 gram total load and 500 cycles = 32 mg loss
FLEXURAL STRENGTH: 5,400 psi @ ASTM D790
COMPRESSIVE STRENGTH: 9,100 psi @ ASTM D695 – 1/2 ”X 1/2” bars
ADHESION: 450 psi @ elcometer (concrete failure, no delamination)
VISCOSITY: Mixed = 1300-2300 cps (typical, most colors)
TENSILE STRENGTH: 4,800 psi @ ASTM D638
ULTIMATE ELONGATION: 3.1%
GARDNER VARIABLE IMPACTOR: 50 inch pounds direct – passed
HARDNESS: Shore D = 80

PRODUCT STORAGE: Store product at normal room temperature. Continuous storage should be between 60 and 90 degree F. Low temperatures or temperature fluctuations may cause product crystallization.
SURFACE PREPARATION: The most suitable surface preparation would be a fine brush blast (shot blast) to remove all laitance and provide a suitable profile. All dirt, foreign contaminants, oil and laitance must be removed to assure a trouble free bond to the substrate. A test should be made to determine that the concrete is dry; this can be done by placing a 4’X4’ plastic sheet on the substrate and taping down the edges. If after 24 hours, the substrate is still dry below the plastic sheet, then the substrate is dry enough to start coating.
PRODUCT MIXING: This product has a mix ratio of 12# part A to 4.15# part B or two parts A to one part B by volume for standard colors. Standard packages are in pre-measured kits and should be mixed as supplied in the kit. We highly recommend that the kits not be broken down unless suitable weighing equipment is available. After the two parts are combined, mix well with slow speed mixing equipment such as a jiffy mixer until the material is thoroughly mixed and streak free. After mixing, transfer the mixed material to another pail (the transfer pail) and again remix. The material in the transfer pail is now ready to be applied on the primed substrate. Improper mixing may result in product failure.
PRIMING: A suitable primer should be used before applying this product. See the front side of this technical data for primer information. If a primer is not used, more porous substrates may cause outgassing and possible surface defects.
PRODUCT APPLICATION: The mixed material can be applied by brush or roller. However, the material can also be applied by a suitable serrated squeegee and then back rolled as long as the appropriate thickness recommendations are maintained. Maintain temperatures and relative humidity within the recommended ranges during the application and curing process. If concrete conditions or over aggressive mixing causes air entrapment, then an air release roller tool should be used prior to the coating tacking off to remove the air entrapped in the coating.
RECOAT OR TOPCOATING: If you opt to recoat or topcoat this product, you must first be sure that the coating has tacked off before recoating. However, all previous coats should be deglossed to insure a trouble free bond prior to application of recoats or topcoats. Colder temperatures will require more cure time for the product before recoating or topcoating can commence. Before recoating or topcoating, check for epoxy blushes (a whitish, greasy film or deglossing). If a blush is present, it can be removed by any standard detergent cleaner prior to topcoating or recoating. Many epoxy coatings and urethanes as well as multiple coats of this product are compatible for use as a topcoat.
CLEANUP: Use xylol. (xylene)
FLOOR CLEANING: Caution! Some cleaners may affect the color of the floor installed. Test each cleaner in a small area, utilizing your cleaning technique. If no ill effects are noted, you can continue to clean with the product and process tested.
RESTRICTIONS: Restrict the use of the floor to light traffic and non-harsh chemicals until the coating is fully cured (see technical data under full cure). It is best to let the floor remain dry for the full cure cycle.

100% Solids/Norklad 200 Color Chart

 
75 sq/ft
150 sq/ft
350 sq/ft
1,500 sq/ft
 
Buy Now
Buy Now
Buy Now
Buy Now

Norklad 200 - 100% Solids Epoxy "Fast Cure" Colored Base CoatNorklad 200 - 100% Solids Epoxy "Fast Cure" Colored Base Coat

 

 

 


Buy Now


Norklad 200 LVP - 100% Solids Epoxy "Low Viscosity Primer" Colored Primer CoatNorklad 200 LVP - 100% Solids Epoxy "Low Viscosity Primer" Colored Primer Coat

 

 

 



Buy Now


 
Epoxy Superstore Footer
COPYRIGHT   NORKAN,  INC.  -  ALL RIGHTS RESERVED    -  CALL FOR INFO: 1-800-227-8479
Norkan Inc - 26200 Groesbeck Hwy - Warren, MI 48089  USA   1-800-227-8479